Before starting, you ensure your hands and nails are well cleaned. File your nails if necessary, so that there are no snags. By doing this you prevent damages on the face and risk of infection.
Always work using clean materials (sponges, brushes, spatulas, water bowls) and change the water regularly.
Get the subject to put on any clothes beforehand that have to be put on over the head. Protect your models clothing with a hairdressing cape or a towel.
Place the applications on the skin to get an impression of whether the edges are a good fit and where it is going to be glued on. Apply Transparent Powder to where the edge merges into the skin to mark out the exact spot.
Protect the eyes by closing them and covering them with a tissue. Can cause serious damage to the eyes.
To get a smooth transition between the latex prostetic and the skin, even the edges off as follows: apply a thin line of eyelash adhesive to the edge of a sponge and dab this over the transition between the latex prostetic and the skin. Allow to dry with help of a hairdryer until the result is transparent. Colour the edges of the transition with the colour being used. Powder it all off with Grimas Transparent Powder or Fixing Powder and then remove any excess powder. Dab the application with a Stipple Sponge to apply the effect of a skin structure.
The application covers the eyebrow.
Take the Crème Make-up Pure out with a clean spatula and work from the spatula. Apply it with a slightly damp latex sponge or make-up sponge onto the skin.
You can use Wool Crepe to create rough, exaggerated eyebrows, which you apply at unequal heights, as the character has an asymmetrical face.
Press the obliquely cut surface onto the adhesive and work the Wool Crepe eyebrows outwards. You use scissors to create the desired model for the eyebrows. If necessary, open the structure a little and model them using the end of a pin-tail comb or the back of a brush. Repeat the process of cutting and opening if necessary until the desired result has been achieved.
Important areas for shading are the eye sockets, the temples, the side of the nose and below the cheekbones. You draw the lines with a flat sable-hair brush. By placing it obliquely on the skin you get a sharp edge on one side and a fading effect on the other side. To determine which side should be sharp and which side faded, you start from the centre of the face (nose). Create a fading effect towards the outside.
The parts of the face that have not been shaded now seem to have been brought forward.
You powder the face off with Grimas Transparent Powder, Fixing Powder or Make-up Powder. Apply the powder on top of the make-up. You can do this with a Make-up Sponge or a Velour Powder Puff. Allow to settle in and remove excess powder with a Powder-Rouge Brush.
Wool Crepe that has been stuck on with Mastix Extra you remove with Mastix Remover. You can then already pull some of the hairs loose and remove them with a tissue. The remaining hairs and the adhesive you remove with a cotton wool pad and Mastix Remover. Dab it carefully onto the skin and roll the residual material off the skin.
Removing a latex application: wipe a cotton bud soaked in Grimas Mastix Remover along the adhesive edge to loosen it. Remove the adhesive and make-up residues from the latex prostetic with Mastix Remover.
Massage Grimas Multi Remover Pure or Cleansing Cream into the skin and remove with a tissue. Cleanse the skin afterwards with cleansing lotion.
Store the make-up in a dry and cool place until the next time you use it.
The sponges are disposable so you can throw them away after use. If you do want to reuse them, first rinse them under the tap with some soap or shampoo or wash them in the washing machine (in a net bag or pillow case), set to at least 60°C.
You can clean brushes with water and soap or shampoo. Put the moist hairs of the brushes back into shape by hand after washing. Dry the brushes lying flat on a towel and do not place them upright, since that causes the moisture to run down into the shaft.
Clean the latex prostetic afterwards using water and soap, and powder it with Grimas Transparent Powder after drying (with a dryer, if necessary). Keep in a dark place.